I learned about OS-9 in early 1983, when it was new. What I heard mainly concerned BASIC09 and at that time BASIC didn't interest me. That was unfortunate. OS-9 is a miniature Unix clone, optimized for the 6809.
 |
| Baud rate generator and counter/timer board |
Requirements
By fall of 1986, I tired of the limitations of Flex09, and started looking at OS-9. Bringing up an OS-9 system didn't have the same challenges as Flex09, since OS-9 can format 8" diskettes. OS-9 does have additional hardware requirements. It needs a periodic source of interrupts.
Interrupt Logic
The OS-9 CLOCK module has logic for several interrupt sources, using chips available at the time. The MC6840 programmable counter/timer chip, with three 16-bit programmable counter/timers, was one option. The MC6840 fit nicely on the bit rate generator board. The driver allowed two circuit variations.
The circuit I chose exercises all three counter/timers. Timer 1 counts 50,000 cycles, then trips Timer 2 and 3. Timer 2 counts twice and signals an interrupt. Timer 3 counts down from 90. In this way, Timer 2 provides regular interrupts every 50 ms on a 2 MHz system. Timer 3 counts interrupts and adjusts the system clock whether or not the Timer 2 interrupt is serviced every 50 ms.
ROMs
The OS-9 kernel has two modules burned into ROM: OS9p1 and OS9p2. I obtained two 2KB ROMs and programmed them with the images. OS9p1 resides at F800. OS9p1 initializes the kernel, then searches for installed modules, which are position-independent. The second ROM contains OS9p2, Init and Boot. Once OS9p1 finds the OS9p2 module, it initializes it. OS9p2 looks for certain key modules, like IOMan. If they cannot be found, it uses the Boot module to load the rest of OS-9 from a floppy disk.
Once initialized, OS9p2 uses the information in the Init module to start executing. During a soft reset, OS-9 does not always load from disk. If the modules are not altered, OS9p2 can find them and bypass the boot process.
The modular structure of OS-9 allows great flexibility. Modules can be in ROM or loaded from storage devices. The Init module provides the configuration to execute the first module.
Bootstrapping
With a little help from a working OS-9 system, bootstrapping was straightforward. The ROMs I started with were pretty generic SWTPc system ROMs. The MC6840 occupied the bit rate generator board. I borrowed a 5 1/2" disk drive and plugged the DC-2 controller into I/O slot 1, with the 8" controller in I/O slot 2. Armed with a single-sided, single-density 5 1/4" boot disk, I successfully booted OS-9. That was the hard part.
From there, I created a new 5 1/4" boot disk with drivers and configuration for my 8" drives. Booting from this new disk, I formatted 8" disks and moved the OS-9 files to them. I then created an 8" OS-9 boot disk with a new I/O configuration and drivers for both 8" and 5 1/4" drives. At that point, I swapped the floppy disk controller slots, with the 8" controller in I/O slot 1, and the DC-2 in I/O slot 2. (The Boot module is configured to find a WDC-compatible floppy disk controller at the address for slot 1)
At that point, I could boot OS-9 from my 8" drives, and was able to copy files from the 5 1/4" disks. Compared with bringing up Flex09, this was easy.
I tailored my configuration to suit my hardware, and updated the ROMs with customized modules.
Swapping BBUG/Flex09 and OS-9
While I was using OS-9, I would swap back to BBUG and Flex09 on occasion. This was a pain. I would swap out the two 2 KB ROMs and use a different boot disk.
In late October of 1986, I modified the MC6809E V1 board to use a single 4 KB 2732 ROM. This put all of the OS-9 kernel on one chip, and allowed room to expand BBUG. With this modification, only one chip was swapped.
Extended Memory
Working with OS-9 uncovered an issue with extended memory addressing. December 1986, I installed a 74LS21 4-input NAND gate on the SWTPc motherboard to decode the top address bits S0-S3. This placed the I/O addresses at FE000. With the MC6809E V1 board, this worked great with BBUG and Flex09. BBUG initialized the E-block of the DAT with a value F1 -- which the board would interpret as physical address FE000.
However, I found I could not boot into OS-9 any more. Turns out, OS-9 initializes the E-block of the DAT using a value 01, which the board interpreted as physical address 0E000. With the extended addressing decoder on the motherboard, the OS-9 Boot module could not communicate to the I/O devices. This forced me to disable the 74LS21 decoder.
User Experience
OS-9 Level I uses a single 64 KB memory space for the operating system, programs and data. That's not a lot of memory. Many OS-9 programs are small, being written in assembly language. Larger programs, like a compiler, load in as multiple passes, to conserve memory use.
Using OS-9 is cool. It is a real-time, multi-tasking operating system, first available in 1982. Windows wouldn't have comparable functionality until 1989 (Windows NT), and the Mac in 1999 (MacOS X). Like Unix, you can spawn off programs to run concurrently in the background.
Using a second serial port, I ran two users simultaneously, one from the main terminal, and one from the second serial port. I used a Wyse-85 terminal on the main port, and the old CT-64 on the second port. Amazing on an 8-bit machine with 56 KB of memory!
At some point, I hung a modem on the second port. I could leave the machine running at home and dial into it from work.
No comments:
Post a Comment