Rx Antenna Controller

Rx Antenna Controller is QRV.

I started building this unit a couple of months ago. I called it the Beverage Controller, because my motivation was to select amoung the three Beverage antennas I had erected. Yes, I've managed to erect three 500 foot Beverages, one to the NE, SE and NW.

Performance of these antennas is convincing -- 1-2 S-units lower noise than the inverted-L or dipole antennas I use on 160 and 80m, respectively, plus a directional signal boost if the beverage is pointed in the right direction.

I discussed my design issues with this unit in the previous article. Debugging the serial port took another month.

Serial Port Debugging

The reason I had chosen the PIC16F18426 for this design was because of the built-in EUSART. Receiving worked just fine. I could send commands to the controller and it would act on the commands. But it sent no response. 

I had configured the PIC to use RC5 (pin 5) for the EUSART receive input, and RA5 (pin 2) for the EUSART transmit output. After a bit of troubleshooting, I found no action on RA5. It remained at 4.5 V the entire time. Was this a wiring problem, or a programming problem?

I ended up writing another PIC project and setting up a chip on a solder less breadboard to solve this. This project simply sent "Hello World!" at 300 baud every 5 seconds. It also drive two LEDS on the C port pins. The LEDs which alternate during a 1-second startup. When transmitting, the second LED would light up. 

My serial test project worked perfectly. LED 2 flashed for about 1/2 second every five seconds, just as expected. So, why didn't the beverage controller project work?

I modified the beverage controller project to also send "Hello World!" every 5 seconds. Except it didn't work. I traced the wiring in the controller head. RA5 was connected to the MAX232E pin 11. It was the MAX232E that was driving the pin to 4.5 V. With the MAX232E out of the circuit, RA5 stayed at 0 V all the time. It was like the software had configured RA5 as an input, not an output.

I got to the point that I could test both projects on the solder less breadboard. I even programmed the same chip with the serial test project -- and it worked. Programmed the same chip with the beverage controller project -- and it didn't. This was definitely a programming problem.

I tried several modifications of the configuration, eventually applying the serial test project configurations to the beverage controller project. At some point, it started working. I still don't understand what I changed to make it work.

Putting It Together

Remote relay box

After such a struggle, I was happy to finish. I re-programmed the chips to send and receive at 9600 baud. This is plenty fast enough for this purpose.

The controller supports one Kenwood/Elecraft-style command, which takes two forms - a Get and a Set operation:

• Get - &AR; -- responds with &ARn; where n is 1 through 5
• Set - &ARn; where n is 1 through 5 -- selects the antenna specified by n, responds with &ARn;

With the serial port transmit working, I could remotely interrogate the controller to determine which receiving antenna was currently selected. And selecting an antenna would respond to ensure that the controller had received my command.

The controller mounts nicely on the equipment shelf. I used some temporary stick-on labels until I find my computerized label-maker. 

What's Next

The current firmware sends an &ARn; response when a button is tapped. I probably need to make that configurable with a serial command.

I've also thought about adding a scanning feature. The controller could automatically switch antennas after a few seconds. Holding a button could add/remove that antenna from the scan.

However, after a couple of months of using the controller, I've found a glaring deficiency in my design. The Rx Antenna Controller only selects one antenna for the RX ANT port. I use a broadband splitter to also connect to the AUX port for diversity reception. But this only permits diversity reception of one receiving antenna against the transmit antenna. I can't do diversity reception between two receiving antennas. 

What would be nice is to have the remote relay box select the antenna for the RX ANT and AUX port. This would require twice as many relays and a way to control them individually. Doing this requires a re-design of both the remote relay box and the controller box.